The short answer
The Canonet QL17 G-III was designed for one PX625 mercury cell, about 1.35V (Canon’s museum page lists 1.3V). Mercury cells haven’t been made for decades.
The best replacements, in order:
- Wein MRB625 zinc-air (1.35V). The right voltage and size; drops straight in.
- A 675 hearing-aid cell (about 1.4V) in an adapter or with an O-ring. Cheap and close enough for most shooting.
- An MR-9 adapter with a voltage-reducing circuit and a silver-oxide cell. Expensive, but long-lasting.
- A 1.5V PX625A alkaline. Fits and is easy to buy, but can throw exposure off.
The battery runs only the meter and auto mode. The QL17’s leaf shutter is mechanical, so in manual it fires at every speed with no battery, per 35mmc.
How far off is a 1.5V cell?
Sources disagree. Wikipedia says the alkaline cell has no voltage regulation and can cause errors of up to about 1.5 stops: underexposure when the cell is fresh and overexposure near the end of its life. Karen Nakamura found the meter fairly tolerant and says print film handles the error fine.
Our take: for color negative film, a PX625A is fine to get started. For slide film, use a 1.35V option.
The options compared
| Option | Voltage | Fit | Life | Notes |
|---|---|---|---|---|
| Wein MRB625 zinc-air | 1.35V | Drop-in; Ken Rockwell adds a washer for a snug fit | A couple of months to perhaps six once activated (PHSNE) | Runs down after the seal tab comes off, used or not |
| 675 hearing-aid cell | About 1.4V | Smaller; needs an adapter or an O-ring | 2–3 months (ausgeknipst) | Cheapest; a loose fit can lose contact |
| MR-9 adapter + silver oxide | 1.35V | Drop-in holder | Long (silver oxide) | About $40 from C.R.I.S. (PHSNE, Schneider). Look-alikes without electronics give the full 1.55V |
| PX625A alkaline | 1.5V | Drop-in | Long | Voltage sags as it runs down; error changes with time |
| SR44 in a diode adapter | About 1.35V | Adapter | Long | Wikipedia mentions adapters with a Schottky diode |
For more detail on each, see our mercury battery replacement guide.
How to fit and test the battery
The battery check lamp next to the eyepiece is the G-III’s main addition over earlier Canonets. With a fresh cell:
- Fit the cell and press the battery check button. The lamp should light.
- Set the aperture ring to A and point the camera at bright and dark areas. The needle in the finder should swing smoothly through the f-stop scale.
- Compare the reading with a phone meter app in sun, shade and indoors. If it’s off by the same amount each time, set an ISO offset. If the error changes with the light, switch to a 1.35V cell or adapter.
Which cameras take the same battery
The PX625 also powers the meters of the Olympus OM-1, Canon FTb, Minolta SRT 101, Olympus 35 RC and Minolta Hi-Matic 7s, per PHSNE, ausgeknipst and Schneider. The same options work in all of them.
FAQ
What battery does the Canonet QL17 G-III take? A 1.35V PX625 mercury cell originally. Use a Wein MRB625, a 675 hearing-aid cell in an adapter, an MR-9 adapter, or a 1.5V PX625A.
Can I use an LR44 in a Canonet QL17? Not as a drop-in. Wikipedia mentions SR44 adapters with a Schottky diode that drops the voltage to suit the meter.
Does the Canonet QL17 work without a battery? Yes, in manual mode. The shutter is mechanical. Only the meter and auto exposure need power.
Will a 1.5V battery damage the Canonet? No source we found reports damage. The issue is meter accuracy, up to about 1.5 stops off per Wikipedia.