Skip to content
lastroll

Battery · 3V total (2 × 1.5–1.55V, or one 3V lithium)

Nikon FE and FE2 Battery: SR44, LR44 or Lithium, and What Works Without One

Nikon FE, FE2, FM and EM batteries: two SR44 or LR44 cells or one CR-1/3N lithium, how to check them, what still works when they die, and the FE battery drain trap.

Reviewed Nov 21, 20263 min read

The short answer

The Nikon FE and FE2 take two SR44 (silver oxide) or LR44 (alkaline) button cells, or one 3V CR-1/3N lithium cell. So do the Nikon FM and, per later references, the Nikon EM. The cells sit in the base under a cap you unscrew with a coin.

All of these cells are still sold everywhere. Silver oxide (SR44) is the better choice for a light meter: as our LR44 vs SR44 guide explains, its voltage stays almost flat until it’s nearly empty, while an LR44 sags as it ages.

What works without batteries

This is where the four cameras differ:

Camera Without batteries
Nikon FE Only the mechanical M90 (1/90s) and B
Nikon FE2 Only the mechanical M250 (1/250s) and B
Nikon FM Everything except the meter: every shutter speed works
Nikon EM M90 and B. AUTO still fires, at about 1/1000s, per Wikipedia and Allan’s EM FAQ

So the FE and FE2 aren’t dead with flat cells, just limited to one speed. Use a handheld meter or sunny 16. The EM’s trap is that it sounds normal on AUTO with no power, so “it fires” proves nothing about its electronics.

How to check the batteries

  • FE: push the battery-check lever down. If the lamp glows, the cells are good. Richard Haw warns that oxidized contacts can make the check unreliable, so fit fresh cells before you diagnose anything else.
  • FE2: advance to frame 1 and press the release lightly. If the needle swings into the speed scale, the cells are good. Ken Rockwell adds that if the needle drops as soon as you lift your finger, instead of staying on for 16 seconds, the cells are low.
  • FM: pull the advance lever out. If an LED lights, the cells are good.
  • EM: press the battery-check button. The LED beside it should light. If it’s dim or off, check the orientation (plus sides up) or replace the cells.

The FE battery drain trap

The FE’s meter stays on while the advance lever is pulled out. Nikon’s manual warns this will completely drain the cells in a few days. Push the lever back in when you put the camera down. The FM’s meter also switches on with the lever: if its LEDs stay lit with the lever flush, the switch is faulty and will drain fresh cells.

Cold weather and storage

  • Nikon’s FE2 manual warns that cold weather can stop the meter. Keep spare cells warm in a pocket.
  • The FE2 and FM manuals say to remove the cells if the camera won’t be used for a long time; the FE2 manual warns that cells left in can leak.

The Nikon FM2 uses the same cells and has its own page. For other Nikons and the chemistry behind the cells, see our film camera battery guide.

FAQ

What battery does the Nikon FE2 take? Two SR44 or LR44 button cells, or one 3V CR-1/3N lithium cell.

Does the Nikon FE work without batteries? Only at M90 (1/90s) and B. Everything else needs power.

Does the Nikon FE2 work without batteries? Only at M250 (1/250s) and B.

SR44 or LR44 for the FE2? Either fits. SR44 silver oxide holds its voltage better, so the meter stays accurate for longer.

Why do my Nikon FE batteries die so fast? Probably the advance lever is being left pulled out, which keeps the meter on. Nikon’s manual says this drains the cells in a few days.

Cameras that use it

Sources

  1. Nikon FE instruction manual — Butkus.org
  2. Nikon FE2 instruction manual — Butkus.org
  3. Nikon FM instruction manual — Butkus.org
  4. Nikon EM instruction manual — Butkus.org
  5. Nikon FE2 Review — Ken Rockwell
  6. Repair: Nikon FE — Richard Haw's Classic Nikon Repair and Review
  7. Nikon EM FAQ and general information — Allan's Stuff
  8. Nikon EM — Wikipedia
  9. Battery type SR44: compatible cameras — ausgeknipst

Last reviewed Nov 21, 2026.